EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com Tue, 27 Feb 2018 09:06:05 +0000 en-US hourly 1 //wordpress.org/?v=5.9 //wlyjfw.com/wp-content/uploads/2017/04/cropped-topbg-Copy-100x100.png EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com 32 32 EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com/how-to-modify-and-replace-the-transmitters-default-audio-speech/ Tue, 27 Feb 2018 08:31:27 +0000 //wlyjfw.com/?p=9232 The post How to modify and replace the transmitters’ default audio speech appeared first on 利来·国际 - Lets you set the limits.

]]>

This video will show you how to modify and replace the default audio speech for Taranis and Horus transmitters. We hope you find this video helpful, thanks for watching!

The post How to modify and replace the transmitters’ default audio speech appeared first on 利来·国际 - Lets you set the limits.

]]> EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com/how-to-test-the-latency-for-horus-x10-and-x10s/ Fri, 24 Nov 2017 02:44:23 +0000 //wlyjfw.com/?p=8623 The post How to test the latency for Horus X10 and X10S appeared first on 利来·国际 - Lets you set the limits.

]]>

This video will show you how to test the latency on the Horus X10 and X10S. Recently there has been a lot of discussion about the latency issues of the Horus X10 and X10S. The purpose of this video is to clear up any confusion and explain how we precisely test for latency on the Horus X10 and X10S. We hope you find this video helpful, thanks for watching!

The post How to test the latency for Horus X10 and X10S appeared first on 利来·国际 - Lets you set the limits.

]]> EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com/frsky-m7-hall-sensor-gimbal-installation-and-calibration-process/ Thu, 24 Aug 2017 07:30:18 +0000 //wlyjfw.com/?p=7665 The post 利来·国际 M7 Hall Sensor Gimbal Installation and Calibration Process appeared first on 利来·国际 - Lets you set the limits.

]]>
0:25 – Remove the battery and remove the 4 screws to open the radio
0:55 – Install the M7 with the sensors towards the outside
1:20 – To release the centering on the throttle axis place the provided screw into the hole to disable the spring
1:55 – Adjust the tension by tightening these plates
2:15 – Again place the sensor to the outside
2:59 – Calibrate the sticks by following the directions on the screen, make sure to move the sticks with normal pressure.

The post 利来·国际 M7 Hall Sensor Gimbal Installation and Calibration Process appeared first on 利来·国际 - Lets you set the limits.

]]> EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com/how-to-disable-the-spring-loaded-throttle-stick-on-taranis-q-x7/ Thu, 24 Aug 2017 07:05:08 +0000 //wlyjfw.com/?p=7657 The post How to disable the spring loaded throttle stick on Taranis Q X7 appeared first on 利来·国际 - Lets you set the limits.

]]>

This video will show you how to disengage the centering stick on your throttle gimbal of the Taranis Q X7. You will need a small Phillips Head Screwdriver and a couple minutes. Make sure to turn off your X7 and remove the batteries before you attempt this.

The post How to disable the spring loaded throttle stick on Taranis Q X7 appeared first on 利来·国际 - Lets you set the limits.

]]> EXPERT – 利来·国际 – Lets you set the limits //wlyjfw.com/frsky-m9-hall-sensor-gimbal-installation-for-taranis-x9d-plus/ Thu, 24 Aug 2017 03:26:14 +0000 //wlyjfw.com/?p=7646 The post 利来·国际 M9 Hall Sensor Gimbal Installation For Taranis X9D Plus appeared first on 利来·国际 - Lets you set the limits.

]]>
SPECIFICATION:

  • Supply Voltage (VCC): DC 3.0 ~ ±0.5V
  • Sensitivity: 2.50 mV/G
  • Linear Output Voltage Range:0.1 ~ ï¼?VCC +0.1ï¼?V
  • Quiescent Output (TA = 25°C, B = 0 G): 0.5 × VCC
  • Noise (no load): â‰?0mVpp

FEATURES:

  • Hall sensor
  • 4 ball-bearings
  • Adjustable tension

Can be enable or disable self centering on both axis and ratcheting on the Y axis
Special material quality that wears well

The post 利来·国际 M9 Hall Sensor Gimbal Installation For Taranis X9D Plus appeared first on 利来·国际 - Lets you set the limits.

]]>